吉林快三

JILINKUAISAN:NINHAO,JIEDAIHUILINJINANSHIZHANGQINGQUKUNPENGJIQICHANG!

首页 - 消息资讯 >

NIXIAODEMAOHANJIAGONGSHIXUYAOZHUZHONGTIMUYOUNAXIEMA?

时候:2020-04-10
浏览量:
1、铆焊加工时的电器、内燃机、机电、氛围紧缩机等的利用应有完全的防护外壳,一、二次接线柱处应有掩护罩。
1. The use of electrical appliances, internal combustion engines, motors, air compressors and so on in the riveting and welding process should have a complete protective shell, and there should be a protective cover at the one or two junction.
2、焊按操纵及共同职员必须按划定穿着休息防护用品。并必须接纳避免触电、地面坠落、瓦斯中毒和火警等变乱的宁静办法。
2. Welding operators and personnel must wear protective clothing according to the regulations. Safety measures must be taken to prevent accidents such as electric shock, high altitude fall, gas poisoning and fire.
济南铆焊加工
 
3、现场利用的电焊机,应高有防雨、防潮、防晒的机棚,并应装设响应的消防东西。
 
3. The welder used on site should be equipped with rainproof, moisture-proof and sunproof machinery shed, and the corresponding fire-fighting equipment should be installed.
4、施焊现场10m规模内,不得堆放油类、木才、氧气瓶、乙炔产生器等易燃、易爆物品。
4. Within the 10m scope of the welding site, no inflammable and explosive materials such as oil, wood, oxygen bottles, acetylene generators can be stacked.
5、当持久停用的电焊机规复利用时,绝缘电阻不得小于0.5MΩ,接线局部不得有侵蚀和受潮景象。
5. When the long-term outage of the welding machine is resumed, the insulation resistance shall not be less than 0.5M, and the wiring part shall not be corroded or damped.
6、电焊机导线应具有杰出的绝缘,绝缘电阻不得小于1MΩ,不得将电焊机导线放在低温物体四周。
6. Welding machine conductor should have good insulation, insulation resistance should not be less than 1M, welding machine conductor should not be placed near high temperature objects.
7、电焊钳应有杰出的绝缘和隔热才能。电焊钳握柄必须绝缘杰出,握柄与导线毗连应坚固,打仗杰出,毗连处应接纳绝缘布包好并不得外露。操纵职员不得用胳膊夹持电焊钳。
7, the electric welding clamp should have good insulation and heat insulation ability. The grip handle of electric welding clamp must be well insulated, the grip handle should be firmly connected with the conductor, good contact, the connection should be wrapped with insulating cloth and not exposed. The operator shall not hold electric welding pliers with their arms.
8、电焊导线长度不宜大于30m。当须要加长导线时,应响应增添导线的截面。当导线经由过程途径时,必须架高或穿过防护管内埋设在公开;当经由过程轨道时,必须从轨道上面经由过程。当导线绝缘受损或断股时,应当即改换。
8, the length of electric welding wire should not be greater than 30m. When lengthening conductor is needed, the cross section of conductor should be increased correspondingly. When a conductor passes through a road, it must be erected or buried underground through a protective pipe; when passing through a track, it must pass under the track. When the conductor insulation is damaged or broken, it should be replaced immediately.
9、对承压状况的压力容器及管道、带电装备、承载布局的受力部位和装有易燃、易爆物品的容器严禁停止焊接和切割。
9. It is strictly forbidden to weld and cut the pressure vessels and pipes, the charged parts, the bearing parts of the bearing structure and the containers equipped with inflammable and explosive materials in the pressure state.
10、焊接铜、铝、锌等有色金属时,应透风杰出,焊接职员应戴防毒面罩、呼吸滤清器或接纳其余防毒办法。
10. Welding copper, aluminum, zinc and other non-ferrous metals, should be well ventilated, welding personnel should wear anti-virus mask, breathing filter or take other anti-virus measures.
11、当须要焊受压容器、密封容器、油桶、管道、沾有可燃气体和溶液的工件时,应先消弭容器及管道内丈夫力,消弭可燃气体和溶液,而后冲刷有毒、无害、易燃物资;对存有剩余油脂的容器,应先用蒸汽、碱水冲刷,并找开盖口,确认容器洗濯清洁后,再灌满净水方可停止焊接。
11. When a pressure vessel, a sealed container, a tank, a pipe, a pipe, a combustible gas and a solution need to be welded, the husbands' force in the container and pipe should be removed first, the combustible gas and solution should be eliminated, and then the toxic, harmful and flammable substances should be washed, and the container with residual oil should be washed with steam and alkaline water first and found open. Cover the mouth and make sure that the container is cleaned before filling with clear water.
12、当焊接预热焊件温度达150~700℃时,应设挡板断绝焊件收回的辐射热,焊接职员应穿着隔热的石棉服装网www.vhao.net和鞋、帽等。
12. When the temperature of the welding preheating weldment reaches 150~700 C, the radiant heat from the baffle isolating weldment should be set, and the welders should wear insulated asbestos clothing and shoes and caps.
13、地面焊接或切割时,必须系好宁静带,焊接四周和下方应接纳防火办法,并应有专人监护。
13. Safety belt must be fastened when welding or cutting at high altitude. Fire prevention measures should be taken around and below the welding and special guardianship should be taken.
14、雨天不得在露天电焊。在湿润地带功课时,操纵职员应站有铺有绝缘物品的处所,并应穿绝缘鞋。
14, the rain day must not be in the open welding. In wet areas, operators should have insulated goods and wear insulating shoes.
15、应按电焊机额外焊接电流和暂载率操纵,严禁过载。
15, the rated welding current and temporary load rate of electric welder shall be operated strictly without overload.
16、当断根焊缝焊渣时,应戴防护眼镜,头部应避开敲击焊渣飞溅标的目的
16. When removing welding slag, wear protective glasses. The head should avoid the direction of percussion slag splashing.
以上内容是由济南铆焊加工场家供给,想要领会更多的内容,能够存眷咱们的网站,在网站中有更多出色内容等着你!感激你对咱们公司的存眷,但愿这些内容能为你供给赞助!
The above content is provided by the Ji'nan riveting manufacturer. We want to know more about the content. We can pay more attention to our website and have more wonderful content in the website. Thank you for your attention to our company. Hope that these contents can help you!